|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
Anyone ever successfully restore firmware to an Omni
That says “no firmware” it’s dead only has amber power light. I’ve tried a ton of digitest versions even back to PT10 erra. No luck. Usually will say erasing firmware and then hang at that point or hang at 0 percent.
I find it simply retarded that they designed a product that can erase firmware but not restore it. There must be a low level utility that can plug into main board and allow firmware restore. |
#2
|
||||
|
||||
Re: Anyone ever successfully restore firmware to an Omni
Contact support then. The update process may hang for a while but should not be quit before Omni restarts itself. What does the DigiTest say about your unit?
__________________
Janne What we do in life, echoes in eternity. |
#3
|
|||
|
|||
Re: Anyone ever successfully restore firmware to an Omni
Attached is a pic of the digitest. The one is from when it froze and shows current version 1.11 With target as 2.10. Then I tried re running with older version of digitest and it shows no current firmware
Last edited by scenaria; 08-29-2021 at 09:00 PM. |
#4
|
||||
|
||||
Re: Anyone ever successfully restore firmware to an Omni
Before you contact support, have you tried unplugging digilink cable, pressing setup button, scrolling to reset?
__________________
Janne What we do in life, echoes in eternity. |
#5
|
|||
|
|||
Re: Anyone ever successfully restore firmware to an Omni
Front panel is dead. Only thing that lights is amber power button. And yea I’ve tried pressing setup and applying power with no response.
|
#6
|
||||
|
||||
Re: Anyone ever successfully restore firmware to an Omni
Other than random tip of trying a firmware update again with a pre-12.4 digitest version, I would say you need to contact support.
__________________
Janne What we do in life, echoes in eternity. |
#7
|
||||
|
||||
Re: Anyone ever successfully restore firmware to an Omni
I have an OMNI where the front panel will freeze constantly on power-up. It sounds ridiculous, but give it a "gentle" hit underneath it. Maybe a little harder than gentle. Mine comes back to life and all of the displays, buttons, and knobs function again.
__________________
-Ryan Young •2019 Mac Pro 3.5 GHz 8-Core Intel Xeon W - 48 GB 2666 MHz DDR4 (OS 10.15.5) •HD Native PCIe, HD Omni, 192 I/o, Pro Tools Ultimate •Avid S3 + Dock •Blackmagic Intensity Pro (HDMI) •5.1 Room with JBL LSR4300 series
|
#8
|
|||
|
|||
Re: Anyone ever successfully restore firmware to an Omni
I had an Omni that I thought was dead, but it turned out that the contrast settings had changed and blanked out the screen. It happened completely out of the blue. Is there any chance these things have a little battery in them that may need replacing after some years?
__________________
Pro Tools Ultimate 2024.3. OSX 13.6.5. Win 10. HD Native. Lynx AES16e. Lynx Aurora 16. i9-13900KF. ASRock Z690 Steel Legend. 64GB Ram. AMD Vega 64. BM Decklink. Dolby Atmos Renderer 5.2. Trinnov D-Mon. D-Command. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HD OMNI - No firmware, can't install one. | BaroqueWorks | Pro Tools HDX & HD Native Systems (Win) | 2 | 02-13-2020 09:43 AM |
PT HD Omni sin firmware | Limoncarro | Foro en Español | 2 | 05-04-2016 06:30 AM |
The Sticky about the Omni Firmware | YYR123 | Pro Tools HDX & HD Native Systems (Mac) | 5 | 04-25-2016 03:13 PM |
Omni firmware ver. and HW rev. for PT12 | maunaloa | Pro Tools HDX & HD Native Systems (Win) | 2 | 05-15-2015 05:49 PM |
HD Omni firmware update | CDac | Pro Tools HDX & HD Native Systems (Mac) | 3 | 08-01-2011 11:27 AM |