|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
PT 10 HD with non HD hardware?
Hi there,
My studio's out of commission due to the hurricane, and a client is requesting an urgent revision. So I need to figure out a way to open up a PT 10 HD session asap. I'm wondering, if I install my PT 10 HD software onto my laptop, will I be able to use it (without TDM plugs) with my Mbox 2 Mini? Can you chose to use a non-HD playback engine? Also, does anyone know if a session created in PT 10 can be opened in PT 8 if you didn't do the special "save as older version" step? Thanks so much! |
#2
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
You can install the software and it will open as PT10.
You cannot open the PT10 session in an older version. Hope this helps |
#3
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
Quote:
PT 10 HD will run fully featured (apart from TDM obviously) without HD hardware, if you got the iLok with the HD license.
__________________
iMac Pro - MacOS 10.14.6 --- - Pro Tools U HDN 2019.6 - Avid HD Omni + HD I/O 8x8x8 - C|24 | S3 | Dock |
#4
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
Thanks guys! That helps a lot!
|
#5
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
Yes - it'll run just like PT10 with the Complete Production Toolkit
|
#6
|
||||
|
||||
You don't need the MBox either. 'Can monitor from the crappy phone jack if you want...
__________________
Can you please send yourself over fiber to go spam some other forum? Darryl Ramm |
#7
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
yup, you can do that easy.. i was just talking about that on the other thread...
i can boot HD 10 with either my HD Omni via Native, or use 11R as my interface.. you just gotta go over the i/o settings and such as they will all be setup for whatever unit it normally runs through... this can be a pain, its not an exact science when you switch back n' forth like I do so I exported the HD OMNI settings, loaded up again with 11R and configured my i/o's and all that jazz then exported those settings as well.. now i can switch on the fly just by importing the proper defaults... takes a little messin' around at first... but it should work well actually, i like the way its all the same install, and its your ilok key which dictates what features are available to you..
__________________
kickin' at the darkness 'till it bleeds daYlighT
|
#8
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
Exactly. The 10 HD license on the ilok opens 10 HD software on ANY system, Native, MBox, other hardware, etc. Absolutely no difference on your TDM cards or not, except obviously the ability to use TDM plugs.
|
#9
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
If you read 8thnotes post you will see that he is saying what you are saying. He's not wrong, he's actually correct.
|
#10
|
|||
|
|||
Re: PT 10 HD with non HD hardware?
I read his post, and he is wrong, since it's not opening as PT10, but as PT10 HD, which makes a big difference.
__________________
iMac Pro - MacOS 10.14.6 --- - Pro Tools U HDN 2019.6 - Avid HD Omni + HD I/O 8x8x8 - C|24 | S3 | Dock |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
'Unable to locate M-Audio hardware. Make sure your hardware is connected and turned o | roland342 | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 0 | 10-29-2012 09:01 AM |
"Unable to locate M-Audio hardware. Make sure your hardware is connected and turned o | MerryD | Pro Tools SE and Essential (Win) | 8 | 08-02-2012 12:59 AM |
Unable to locate M-Audio Hardware. Make sure your hardware is connected and turned on | ytass | Pro Tools M-Powered (Win) | 4 | 11-25-2009 12:49 PM |
unable to locate m-audio hardware. make sure your hardware is..works fine in ableton? | pein | Pro Tools M-Powered (Win) | 2 | 10-07-2009 12:01 AM |
unable to locate M-Audio hardware. Make sure your hardware is connected and turned on | joskraus | Pro Tools M-Powered (Win) | 13 | 05-13-2009 09:05 AM |