|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#11
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Gotcha thanks.
I may just bounce it without that plugin and try it in LUNA where I can utilize all the DSP power I have. Best to you... |
#12
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Can't say for sure without actually seeing the circumstance, but any instantaneous change during signal is going to cause a pop/snat/thump. Changes need to be ramped (even by just 10 or 15 msec), or else happen in audio black to be silent. If you can't do either of those then your best bet would be to render that small section (with handles) in audiosuite or as a commit, and then crossfade into/out of the rendered clip.
This problem will be aggravated by sources that have significant amounts of low frequency noise/rumble, or DC offset in the A/D converter, but really, it's just physics. best, rich
__________________
http://www.richbreen.com ---------------------------------------- Mac Studio / Ventura, PT 2023.12.HDX, Avid HD I/Os and Metric Halo ULN8, 3xS1/Dock Also running a Mac Studio Ultra / Ventura / HDX / MTRX / S6 |
#13
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Have you tried adjustting the Steep Breakpoint Smoothing Time in the preferences? I keep mine at 10msec and haven't had this problem since the preference was added to PT a while back. Screenshot attached.
__________________
Pro Tools Ultimate 2023.9 Dell Precision T7600 64 gigs of RAM Windows 10 Pro HD Native PCIe Lynx Aurora with LT-HD Apogee Mytek |
#14
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Hi.
In Preferences - Mixing? I've never touched it. It's currently set at 0 ms with the Automatch at 250 ms. Do you think this will help? What time setting(s)would you recommend? Here's the issue I face. The recording was done live in a television studio. I have a separate audio feed from the mixer and there were two cameras on site as well. When one of the cameramen moved his tripod it caused this loud clang just as the piano was playing the intro to a song. I have identified two frequencies an octave apart that with the correct notch will reduce it immensely without being too noticeable. The spike is less than a second long. That's the issue I face. I'm absolutely welcome to suggestions and appreciate your time. |
#15
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Quote:
__________________
Pro Tools Ultimate 2023.9 Dell Precision T7600 64 gigs of RAM Windows 10 Pro HD Native PCIe Lynx Aurora with LT-HD Apogee Mytek |
#16
|
|||
|
|||
Re: HELP please - Plug-in Automation Pops
Rich and Sleepingtiger, thanks very much. I'll try your suggestions tomorrow.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Automation creates pops/click | Toddhq | Pro Tools 12 | 5 | 05-04-2016 01:44 AM |
Weird volume automation pops | Thenewexhibit | Pro Tools 11 | 10 | 10-23-2015 04:09 PM |
pops & clicks from automation control points? | sound_music | Pro Tools HDX & HD Native Systems (Mac) | 6 | 11-26-2013 07:51 AM |
Random panning automation causing pops clicks???? | Seti Orion | Pro Tools TDM Systems (Mac) | 3 | 02-20-2008 08:29 AM |
Pops & Clicks after writing automation | stayce9665 | Pro Tools TDM Systems (Mac) | 1 | 06-30-2005 01:41 PM |