|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
|
#1
|
|||
|
|||
I/O Error Regarding Output Paths
Getting the following error message which is not allowing me to make any I/O adjustments:
"You haven't assigned outputs for a new output path. Please assign outputs to it, or delete the path." Screenshot attached. Not sure if this is Carbon specific, but it has only recently appeared. Have tried defaulting all tabs as well as deleting all but the main output path. |
#2
|
||||
|
||||
Re: I/O Error Regarding Output Paths
What's the Monitor Path assignment in the bottom right of the Output tab? Try changing that to MON L-R if it's not assigned to that output. If it is assigned to MON L-R, try assigning it to 'no output' and/or a different output path and closing IO Setup. If that works, go back to IO Setup and assign the Monitor Path to MON L-R if necessary.
If that doesn't work, go to Hardware Setup and switch the Headphone Sources to each individual headphone (HP 1 : HP 1, HP 2 : HP 2, etc) and disable Main monitor set, then default IO Setup. If that works then go back to Hardware Setup and re-enable Main and Headphones Sources as desired.
__________________
Kyle Splittgerber Senior Principal Product Designer Avid Berkeley, CA |
#3
|
|||
|
|||
Re: I/O Error Regarding Output Paths
Hey Kyle,
Thanks for responding. No luck with those solutions, unfortunately. The Monitor path assignment is grayed out (attachment 1). When trying to make the hardware setup adjustments and defaulting I/O, the results were strange (attachment 2) and still no luck being able to save them anyway. Same error message as before. |
#4
|
||||
|
||||
Re: I/O Error Regarding Output Paths
Quote:
Also, your ADAT assignments are reversed. Is that intentional? It's really looking like I/O Setup is just in a bad state. Have you tried deleting Pro Tools preferences? If not, do that. Then, create a new session and delete all output paths in I/O Setup, then click Default. Additionally, you can try a settings reset of the Carbon unit if you haven't already: 1 Lower the volume on all output devices and mute your speakers. 2 Power off the unit. 3 Press and hold the Meter button while powering on the unit. 4 Hold the Meter button for 20 seconds while the device front panel is lights in the green start-up state. 5 After this, release the Meter button. The device starts up with the default settings after the Meter button is released.
__________________
Kyle Splittgerber Senior Principal Product Designer Avid Berkeley, CA |
#5
|
|||
|
|||
Re: I/O Error Regarding Output Paths
Quote:
Quote:
I'm having trouble locating Pro Tools preferences (in order to trash) on Big Sur. Can you advise where they would be and which files to delete? Thank you! |
#6
|
||||
|
||||
Re: I/O Error Regarding Output Paths
Quote:
To delete your preferences: –Close Pro Tools and launch Finder. –Click Go and select Go to Folder… –Enter ~/Library/Preferences/Avid and click Go. –Delete the Pro Tools folder. -Relaunch Pro Tools 7050 error indicates a hardware resourcing issue. You can also try changing the Device Configuration in Audio MIDI Setup to see if that has any effect. For how to do that, see pg 42 of the Carbon guide HERE.
__________________
Kyle Splittgerber Senior Principal Product Designer Avid Berkeley, CA |
#7
|
|||
|
|||
Re: I/O Error Regarding Output Paths
Kyle- i’m just chiming in here to say that I had the same I/O dialog problems and got the same error message that the original poster detailed in his first post. I deleted my preferences and it seems to have solved the problem, at least for now. This was a few weeks ago.
Sent from my iPhone using Tapatalk
__________________
Late 2013 Mac Pro (trashcan), 2.7 GHz 12-Core Intel Xeon E5, 64 GB 1866 MHz DDR3 ECC, AMD FirePro D300 2048 MB, Startup disk SSD 512. OSX 10.15.7, Pro Tools 2022.10. Carbon (AVB), Lynx Aurora 16(n) (Thunderbolt) |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Some bus paths could not be mapped to their previous output paths. | Kbiastre | Pro Tools 2019 | 4 | 02-02-2020 03:31 PM |
PT 12.2 not importing multiple output paths | Goombot | Pro Tools 12 | 0 | 10-31-2015 11:17 AM |
Cannot get 5.1 tracks or output paths in Pro Tools 6.4.1 | Berrado | Pro Tools TDM Systems (Mac) | 12 | 06-11-2007 11:35 AM |
Cannot get 5.1 tracks or output paths in Pro Tools 6.4.1 | Berrado | Post - Surround - Video | 4 | 06-11-2007 11:34 AM |
How do I select multiple output paths? | syra | Pro Tools TDM Systems (Mac) | 5 | 10-21-2003 12:39 AM |