Avid Pro Audio Community

Avid Pro Audio Community

How to Join & Post  •  Community Terms of Use  •  Help Us Help You

Knowledge Base Search  •  Community Search  •  Learn & Support


Avid Home Page

Go Back   Avid Pro Audio Community > Announcements > General

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-12-2006, 03:45 AM
Avid's Avatar
Avid Avid is offline
Administrator
 
Join Date: Apr 1998
Location: Worldwide
Posts: 9,579
Default Pro Tools HD 7.1cs8 Updates

Pro Tools HD 7.1cs8 for Mac OS X & Windows XP

Available for download from the Pro Tools HD 7.1, Pro Tools|HD PCI and PCIe sections in the Support section:
http://www.digidesign.com/support

In addition to all previous fixes, Pro Tools HD 7.1cs8 for Mac OS X & Windows XP both added the following:

Fixed: Some International Characters Were Not Allowed In Pro Tools 7 Sessions (Item # 71269 and 76222)
German, Norwegian, Swedish, and French/French Canadian characters were affected. DigiBase search criteria was also affected.

Fixed: When Controlling 9-pin Devices with MachineControl, Selections Could Appear on the Timeline When Fast-Winding Pro Tools (Item #75405)
This would occur when the Machine Follows Edit Insertion/Scrub preference was enabled.

Fixed: Pro Tools Always Overwrites Automation in Existing Playlists When Using "Import (Session Data): Overlay New on Existing Playlists" (Item # 63172)
Pro Tools would not allow a session with a 2-hour start time to overlay automation data on a session with a 1 hour start time without clearing all automation before 2 hours on the destination session.
- Automation cannot be "combined" with an overlay—the destination session’s automation will be replaced from the Session Start time of the source session.
- Inserts and sends must be consistent between sessions or they may be overwritten

Fixed: Volume Automation From a Control Surface May Be Inaccurately Written if the System Is Under Load (Item# 75888)
This could occur with high track count sessions when using the surround mixer.

Fixed: When Controlling a Non-Linear Device with MachineControl in "Transport=Pro Tools," Taking Pro Tools Off Line Would Send a "Stop" Command (Item# 77280)
This could stop another 9-pin device in the system unnecessarily.
- This change in behavior is activated only by the "Non-Linear Transport Error Suppression" preference.

The Following Fix is also included in Pro Tools HD 7.1cs8 for Windows XP Only:

Fixed: Scrubbing or Shuttling on a Record-Enabled Track While In QuickPunch could Cause a Reboot (Item #76766)
This would occur when a ReWire plug in was being used in the session or when scrubbing on a track with an RTAS plug-in inserted.
__________________
Administrator
Avid Pro Audio Community
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Pro Tools HD 7.1cs8 Updates Avid Pro Tools TDM Systems (Mac) 39 07-26-2006 05:12 AM
Pro Tools LE & M-Powered 7.1cs8 Updates GenerationM General Discussion 1 07-21-2006 08:06 PM
Pro Tools LE & M-Powered 7.1cs8 Updates Hype General Discussion 0 06-21-2006 06:19 PM
Pro Tools HD 7.1cs8 Updates Avid Pro Tools TDM Systems (Win) 0 06-12-2006 03:48 AM
Pro Tools LE & M-Powered 7.1cs8 Updates Avid General 0 06-12-2006 03:24 AM


All times are GMT -7. The time now is 11:37 AM.


Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com