Eucon 3 - Artist Control not connecting to PT

[Trazan]

Crap. Just updated from 2.7.1 hoping for a perfectly stable 3.0. Not working at all.

Artist Control recognizes Pro Tools as the program in focus, but is not connecting. No transport lights, no tracks....no fun.

Pro Tools 10 - various versions, up to 10.3.5.
OSX 10.7.5

Anyone got this setup to work? Ideas?

[DrFord]

Exact same problem.

Have you installed 2.7.1 again? Were you having problems of stability in this system?

[Trazan]

Originally Posted by DrFord

Exact same problem.

Have you installed 2.7.1 again? Were you having problems of stability in this system?

Yes, went back to 2.7.1. Works for now.

Parts of the surface disconnects every now and then. Not sure why. It has been working fine this last week, so I'm suspecting it must be some kinda scenarios in PT that triggers it.

[ECmaj7]

Eucon Artist sometimes connects sometime doesn't.
I work in Pro Tools10, 11, Cubase 7 and Logic 9, X...
doesn't matter what DAW I'm using so we know it's a Eucon problem.

EC

[DanielEUCON]

Here is another item to quickly try and let us know if it works:

If you get into a bad connectivity state, please try the following:
-Go to System Preferences > EUCON and press Stop (make sure Pro Tools or other EUCON DAWs are not running)
- wait 30seconds and press Start.
- Once the Surfaces are attached in EuControl, check that the local Workstation is available in the Workstations tab, and it is Attached.
- Launch Pro Tools (or other EUCON DAW).

Does the system connect and work with Pro Tools after these steps?

[Redmusichead]

Originally Posted by DanielEUCON

Here is another item to quickly try and let us know if it works:

If you get into a bad connectivity state, please try the following:
-Go to System Preferences > EUCON and press Stop (make sure Pro Tools or other EUCON DAWs are not running)
- wait 30seconds and press Start.
- Once the Surfaces are attached in EuControl, check that the local Workstation is available in the Workstations tab, and it is Attached.
- Launch Pro Tools (or other EUCON DAW).

Does the system connect and work with Pro Tools after these steps?

I had the same problem. My Artist Control recognized both Pro Tools and Logic, but it didn't connect properly. No faders worked with the tracks, and the touch screen wouldn't respond to anything.

I followed the instructions from DanielEUCON, and it worked instantly. Thanks!


iMac 3.4 GHz Intel Core i7 16GB RAM OSX 10.7.4 Pro Tools 10.3.2 Logic 9.1.8 Avid MC Artist Control

[OTARI]

Eucon 3.0.1
PT HD 10.3.7
OSX 10.8.5 / fresh System

- after system boot, I stop and re-start Eucon
- start Artist Mix and Transport
- start Pro Tools

surfaces connect only in 25% of the cases
often lose connection when switching between, e.g., ProTools and Finder
(Surfaces are locked to ProTools in Eucon settings)

please get this straight once and for all.
I mean, for long has this piece of software in development?

[Artist PM]

Originally Posted by OTARI

Eucon 3.0.1
PT HD 10.3.7
OSX 10.8.5 / fresh System

- after system boot, I stop and re-start Eucon
- start Artist Mix and Transport
- start Pro Tools

surfaces connect only in 25% of the cases
often lose connection when switching between, e.g., ProTools and Finder
(Surfaces are locked to ProTools in Eucon settings)

please get this straight once and for all.
I mean, for long has this piece of software in development?

Email me directly if you haven't already. We will get you sorted.

[CYork]

We decided to finally make the move to PT11 now that Waves, McDSP and Native Instruments are finally there. But it's looking like our control surfaces are not there yet??

MC Controls and Mixes all work fine with PT10 and Eucon 2.7.1 on Windows 7.

Install Eucon 3.0.1 and no go with PT11.

I get this error message about 50% of the time when I reboot:
"Eucon client can not access the bonjour service and will now exit.
Please check your Bonjour installation and service settings."

Any work arounds?

Chad

[southboundloco]

You have to manually start MC-Client then EuControl. wait till the computer has finished connecting to the network

www.joshuamanlunas.com