|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
OPTICAL i/o troubles
Hi to all at DUC
Have a problem with the connection of my KORG 168RC digital console via optical cable. Have Powerbook + DIGIRACK002, use the 168RC for 8 additional channels connected via opti-cable. Problem: during recording all 8 channels from 168RC have from time to time a noise of a loud "knack" which even gets worse (means: gets more often) as longer I do record. Did someone had the same problem? Looking fwd to yr help musical greetings from LUX Serge |
#2
|
|||
|
|||
Re: OPTICAL i/o troubles
Make sure the clock source in ProTools is set to optical and the clock settings in the Korg is set to internal and that the sample rates are set to the same thing on both as well..
__________________
MacPro3ghz, 6GB, 10.7.5, PT10.3.2, Digi002 factory/toolkit2/PTIEP, 11R |
#3
|
|||
|
|||
Re: OPTICAL i/o troubles
Quote:
Thats a very good starting point to fix your problem. Change the clock source to ADAT and it should work. Mats B |
#4
|
|||
|
|||
Re: OPTICAL i/o troubles
oops sorry ADAT is the correct PT setting..
__________________
MacPro3ghz, 6GB, 10.7.5, PT10.3.2, Digi002 factory/toolkit2/PTIEP, 11R |
#5
|
|||
|
|||
Re: OPTICAL i/o troubles
Dear ALL
Flommer thanks for yr reply BUT however this seems to not solve the problem... When I set the Korg digital mixer to be the source, DIGIRACK switches from 44.1 to 96 but in the SETUP DIGI RACK is well set to 44.1 Could y pls once more help me to solve this problem thanks very much serge |
#6
|
|||
|
|||
Re: OPTICAL i/o troubles
I found a manual for your 168rc on line and I can't be sure (cause I don't have time to read the whole thing!) but it looks like the mixer only outputs digital at 48khz sampling rate. Make sure the mixer's clock source is set to "internal".
Set ProTools like this: In Setup -> Hardware In the "Digital Input" section at the top, choose Optical = ADAT and for the "Clock Source" choose "ADAT" If you can change the sample rate, set it to 48khz. You might not be able to if PT automatically sets the sample rate based on what it is receiving at the port. One final thing I'm not sure about is that you may have to have your session created at 48khz as well. I think you should also create the session at 24 bit, because the digital out on your korg is 18 bit and at 16 bit it might get chopped off. here's the manual in case you don't have it: manual Give it a try...
__________________
MacPro3ghz, 6GB, 10.7.5, PT10.3.2, Digi002 factory/toolkit2/PTIEP, 11R |
#7
|
|||
|
|||
Re: OPTICAL i/o troubles
Hi Flommer,
Thanks for yr add advice! B U T unfortunately it is NOT working ... getting frustrated right now Opened a new session, set it to 48kHz but as soon as I want to change to ADAT in the PT section I get an error message saying external clock source not correct??? Korg Mixer is set to internal Exchanged cables, so this can't be the problem anyone with a solution ??? thanks for yr help Serge |
#8
|
|||
|
|||
Re: OPTICAL i/o troubles
I don't have the Korg mixer that you are trying to use but I do use an Alesis QSR that I have connected to the ADAT port and it works with the settings I mentioned, with no clicks or funny behavior. I did get the same error in a test session when the sample rate in PT was set to 48 and the QSR was set to 44.1 (I keep my sessions at 44.1) but I changed the QSR to 48, reset ProTools to follow the external sync again and all was OK. I would suggest reading the manual for your korg carefully to make sure what sample rates it will support when it is set to sync internally. If that doesn't help then I am out of suggestions... Sorry
(Now I need to set everything back to 44.1 before I forget )
__________________
MacPro3ghz, 6GB, 10.7.5, PT10.3.2, Digi002 factory/toolkit2/PTIEP, 11R |
#9
|
|||
|
|||
Re: OPTICAL i/o troubles
Hi
did try this already but again this did not solve the probleme Think the Korg is of no use anymore ... serge |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
003 and Digimax, lightpipe optical troubles!! (HELP!) | hw2nw | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 5 | 12-17-2007 09:01 AM |
Clock Issue on 192 i/o Optical [ADAT] Not Optical [Encl] | Willard | Pro Tools TDM Systems (Mac) | 1 | 10-10-2007 01:23 PM |
Troubles with changing SPDIF to optical :-(( | ISedlacek | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 5 | 11-15-2003 12:22 PM |
192 : MUST select Optical format for Bay 3 to activate Enclosure Optical inputs????? | el biciclista | Pro Tools TDM Systems (Mac) | 2 | 07-09-2002 10:32 AM |
whats the difference between adat optical and spdif optical? | Vegadark | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 10 | 04-07-2002 07:42 PM |