Avid Pro Audio Community

Avid Pro Audio Community (https://duc.avid.com/index.php)
-   AAX Plug-ins (https://duc.avid.com/forumdisplay.php?f=98)
-   -   Avid Pro Multiband Dynamics Plug-in - deapth versus ratio (https://duc.avid.com/showthread.php?t=363962)

Gm167704 02-03-2015 12:17 PM

Avid Pro Multiband Dynamics Plug-in - deapth versus ratio
 
Hi there,
I am interested in purchasing Avid's Pro Multiband Dynamics - I am trying to get a bit more clarity as to how the depth setting works and how i can clearly understand it's relationship to a more classic ratio control. i think i am just generally confused and could use some wisdom.

the manual states:

The Depth control sets the maximum amount of gain reduction or expansion applied to the input signal of the band (from –24 dB to +24 dB). For example, if you set Depth to –10 dB, no more than 10 dB of gain reduction is applied to the incoming signal. You can also adjust the Depth setting using the purple triangle Depth control on the FFT display.

So, if i understand this correctly then, depth simply sets a limit to how much compression or expansion can happen to a given signal right? So does that mean that the Pro multiband dynamic has a ratio in which it compresses and expands signals that is nonadjustable? and instead uses deapth as it functions in a generally similar way? perhaps due to it's also being an expander?

thanks guys

Drew Mazurek 02-03-2015 01:32 PM

Re: Avid Pro Multiband Dynamics Plug-in - deapth versus ratio
 
Quote:

Originally Posted by Gm167704 (Post 2228838)
Hi there,
I am interested in purchasing Avid's Pro Multiband Dynamics - I am trying to get a bit more clarity as to how the depth setting works and how i can clearly understand it's relationship to a more classic ratio control. i think i am just generally confused and could use some wisdom.

the manual states:

The Depth control sets the maximum amount of gain reduction or expansion applied to the input signal of the band (from –24 dB to +24 dB). For example, if you set Depth to –10 dB, no more than 10 dB of gain reduction is applied to the incoming signal. You can also adjust the Depth setting using the purple triangle Depth control on the FFT display.

So, if i understand this correctly then, depth simply sets a limit to how much compression or expansion can happen to a given signal right? So does that mean that the Pro multiband dynamic has a ratio in which it compresses and expands signals that is nonadjustable? and instead uses deapth as it functions in a generally similar way? perhaps due to it's also being an expander?

thanks guys

Ratio is a "moving" parameter (slope) given that it depends on the amount over the threshold the signal is.
http://www.uaudio.com/media/blog/2009/11/basics_02.jpg
Depth is simply a defined maximum amount of gain reduction that can happen no matter what.

So even as your signal continues to get louder and you'd expect to see more gain reduction, the Depth "stops it" at that set amount.

Make sense?

Farhoof 02-03-2015 01:42 PM

Re: Avid Pro Multiband Dynamics Plug-in - deapth versus ratio
 
Quote:

So, if i understand this correctly then, depth simply sets a limit to how much compression or expansion can happen to a given signal right?
Correct.
Quote:

So does that mean that the Pro multiband dynamic has a ratio in which it compresses and expands signals that is nonadjustable? and instead uses deapth as it functions in a generally similar way?
No the ratio still functions as usual, depth is just a nice extra. You can check the depth setting using the Avid channel strip (non-multiband), it gives a much more understandable visual feedback on how it works.
Beware though Pro Multiband is not using phase linear filters and has audible side effects around the crossover frequencies. I tried it for mastering but it didn't take. Too bad though, other than that it's very nice.


All times are GMT -7. The time now is 07:50 PM.

Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com