|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#121
|
|||
|
|||
Re: "Speed" of rotary knobs
Quote:
Best, Tony |
#122
|
|||
|
|||
Re: "Speed" of rotary knobs
Yay!! Fixed!! It's so much better!
However, i did notice the Monitor control on S3 still accelerates beyond physical movement. (says in the notes the this was addressed).
__________________
Matt McKenzie-Smith mattrixx.net SourceConnect - mattrixx AVID Collab user - mattrixx MacStudio Ultra / LogicProX / IzotopeRX10+ / SourceConnect / MelodyneStudio5 / WAVES Mercury / NI KompleteUltimate / ProToolsUltimate / RME UFX, UFXII, Babyface / AVID S3 + DOCK / Barefoot MM27 gen2 / Barefoot FP01 |
#123
|
||||
|
||||
Re: "Speed" of rotary knobs
Which knob is that ? Do you mean the Dock or the Physical I/O control ?
|
#124
|
|||
|
|||
Re: "Speed" of rotary knobs
Sorry, I should have clarified.
All the level controls for the S3 AVB (accessed by Expand/Page + Page). update** Now, this is going to sound really weird, but I just jumped in there again and they're better than a few minutes ago.. i.e. they don't run on after a fast twist. It's like they needed to be accessed, then left and then back in again. (That sounds confusing). great update!!! Love it!
__________________
Matt McKenzie-Smith mattrixx.net SourceConnect - mattrixx AVID Collab user - mattrixx MacStudio Ultra / LogicProX / IzotopeRX10+ / SourceConnect / MelodyneStudio5 / WAVES Mercury / NI KompleteUltimate / ProToolsUltimate / RME UFX, UFXII, Babyface / AVID S3 + DOCK / Barefoot MM27 gen2 / Barefoot FP01 |
#125
|
||||
|
||||
Re: "Speed" of rotary knobs
We only updated the EUCON knobs, didn't think the hardware controls needed anything. Hopefully its all OK now.
|
#126
|
|||
|
|||
Re: "Speed" of rotary knobs
So it doesn't apply to the - "The Control Room/Monitor knob is linear (no acceleration)" on the S3?
__________________
Matt McKenzie-Smith mattrixx.net SourceConnect - mattrixx AVID Collab user - mattrixx MacStudio Ultra / LogicProX / IzotopeRX10+ / SourceConnect / MelodyneStudio5 / WAVES Mercury / NI KompleteUltimate / ProToolsUltimate / RME UFX, UFXII, Babyface / AVID S3 + DOCK / Barefoot MM27 gen2 / Barefoot FP01 |
#127
|
||||
|
||||
Re: "Speed" of rotary knobs
Only Eucon Monitoring knobs. Is there a problem with the S3 internal I/O knob control ?
|
#128
|
|||
|
|||
Re: "Speed" of rotary knobs
Just a slight one.
When a adjusting the encoders, they have a tendency to overrun, when turned quickly. I don't tend to use it very often, but it can be a little disconcerting.
__________________
Matt McKenzie-Smith mattrixx.net SourceConnect - mattrixx AVID Collab user - mattrixx MacStudio Ultra / LogicProX / IzotopeRX10+ / SourceConnect / MelodyneStudio5 / WAVES Mercury / NI KompleteUltimate / ProToolsUltimate / RME UFX, UFXII, Babyface / AVID S3 + DOCK / Barefoot MM27 gen2 / Barefoot FP01 |
#129
|
|||
|
|||
Re: "Speed" of rotary knobs
first impressions are good, but no fine control? or am I missing something?
|
#130
|
|||
|
|||
Re: "Speed" of rotary knobs
The response of the knobs is definitely better. Much more predictable and much more useable.
In an IDEAL world, I would have liked user adjustable controls for acceleration, and sensitivity but still.... the new improvements get a definite thumbs up from me. Thanks Avid! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Does "Westmere" qualification apply to "Bloomfield" and "Gulftown" also? | bashville | Pro Tools 10 | 5 | 03-23-2013 03:04 PM |
hardware buttons for "preview", "capture" and "punch" | evs | Post - Surround - Video | 1 | 12-06-2010 12:28 PM |
"Slowing down the tape speed" | bsmith23 | Tips & Tricks | 6 | 05-11-2009 07:03 PM |
"Tape" speed | MacSean112 | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 20 | 07-01-2003 12:19 AM |
The "FATE" of CM LABS "MotorMix" & "MotorMate". Dum dum dum dum... | leon777 | Pro Tools TDM Systems (Mac) | 21 | 10-15-2002 12:00 AM |