|
Avid Pro Audio CommunityHow to Join & Post Community Terms of Use Help Us Help YouKnowledge Base Search Community Search Learn & Support |
#1
|
|||
|
|||
Why is \"Paste, on the fly\" a no go?
Grabbing a region I wanted to "pop it in" at several places, it was a guitar riff, and there is no math or set patterns to my arrangement decisions, I put things here, there, everywhere, like anyone.
While rolling I pressed the Apple V command to paste the riff "on beat", it wound up way back from where the cursor was (which was a bore) & when I pressed Apple V again nothing happened!No further pastes possible. What is this? Do one paste then stop functioning? How can I "pop things in" on the fly intuitively with no grids, markers etc? Obviously a sampler could do it but PT has got to be better that that , aint it? I RTFM, I must have missed it. How is this most basic task done by you guys out there? I am sure I have seen my chums running Logic Audio do it, what about Pro Tools? Thanks Jules |
#2
|
|||
|
|||
Re: Why is \"Paste, on the fly\" a no go?
Make sure the track you want to paste to is the active track and while in playback, hit the down arrow before you paste.
Rail ------------------ Recording Engineer
__________________
Platinum Samples www.platinumsamples.com Engineered Drums for BFD |
#3
|
|||
|
|||
Re: Why is \"Paste, on the fly\" a no go?
I see yes! Thanks! Once I got into groove with
apple V - down arrow! apple V - down arrow! apple V - down arrow! apple V - down arrow! apple V - down arrow! In / out / shake it all about! I was able to paste short funky guitar riffs in the right spots & very nearly in time, needing just a bit of nudging afterwards! V happy! Thanks again! Was that in the manual? If so what page, I can't find it! Jules Be nice to have that on one button hit on PT 5 eh? [This message has been edited by Julian Standen (edited 10-14-99).] |
#4
|
|||
|
|||
Re: Why is \"Paste, on the fly\" a no go?
Well it is in the manual, but not stated the way you expect no doubt.
The down arrow is documented as being the method to grab the playback cursor location and place the edit cursor at that location (remember that there are two cursors - the playback and the edit cursor). Paste, simply always pastes to the edit cursor position. So when you hit the down arrow you're simply placing the edit cursor at the desired location (where the playback cursor is) - and when you paste, that's where it goes. If you wanted to - you could easily create a macro to do this with QuicKeys. PT 5.0 does have some macro capability built in I believe - so perhaps this will be possible to automate without QuicKeys. Rail ------------------ Recording Engineer
__________________
Platinum Samples www.platinumsamples.com Engineered Drums for BFD |
#5
|
|||
|
|||
Re: Why is \"Paste, on the fly\" a no go?
I will create a macro button for it, thanks
Jules [This message has been edited by Julian Standen (edited 10-15-99).] |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Copy... Paste... Paste... Paste...? | accession | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 9 | 01-18-2022 04:18 PM |
copy and paste EVERYTHING | aldersyde | Pro Tools 10 | 1 | 06-10-2012 09:23 AM |
Copy works paste doesnt paste??? | SoMedia | Pro Tools M-Powered (Win) | 12 | 01-04-2011 01:19 PM |
cut and paste? | STUDIO A | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 3 | 02-26-2004 09:19 AM |
cut and paste | Tom Harmon | General Discussion | 1 | 11-17-2000 09:33 AM |