Anyone install Lexicon PCM bundle?

[Mr. Kelly]

Hey there,

I'm having trouble installing the Lex PCM bundle. I have attempted the install with all protocol seeming in place. When open PT, the plugs don't show up in my plug menu. Ughhhh....

I run W7 64, on PT 10.3.9

- software shows up in program list
- ilok license activated and on correct ilok 2
- using the correct installer, which supports AAX/RTAS

Anybody have had similar experience, or have insights as to what might have happened???

Thanks for anything you may know!

[zion]

Originally Posted by Mr. Kelly

Hey there,

I'm having trouble installing the Lex PCM bundle. I have attempted the install with all protocol seeming in place. When open PT, the plugs don't show up in my plug menu. Ughhhh....

I run W7 64, on PT 10.3.9

- software shows up in program list
- ilok license activated and on correct ilok 2
- using the correct installer, which supports AAX/RTAS

Anybody have had similar experience, or have insights as to what might have happened???

Thanks for anything you may know!

I'm on Mac and PT 11.3.1 HD but I hand the same problem installing the Total PCM Bundle so what I had to do was uninstall the Total Bundle and install the Lexi effects plug bundle and then install the Lexi Reverb bundle which is whats in the Total bundle and I was good to go. The iLok saw them both as the Total Bundle. For some reason the PCM Total Bundle installer didn't install properly for me.

[Mr. Kelly]

Thanks Zion.

I was erroneous describing what I actually installed. I said it was the full bundle, but I was really attempting to install just the REVERB bundle, not the full bundle.

Think something similar is happening? What else could I do?

Did Lexicon give you that workaround?

[zion]

Originally Posted by Mr. Kelly

Thanks Zion.

I was erroneous describing what I actually installed. I said it was the full bundle, but I was really attempting to install just the REVERB bundle, not the full bundle.

Think something similar is happening? What else could I do?

Did Lexicon give you that workaround?

I haven't talked to Lexicon I just tried the other installers and it worked. Have you tried uninstalling it and Installing it again?

[Mr. Kelly]

Yup, tried reinstalling... twice.

I also tried to figure out whether I got the ilok authorization number typed in wrong, but I can't even find out where to find again the authorization number!

All else w. the ilok part looks correct.

[YYR123]

Originally Posted by Mr. Kelly

I also tried to figure out whether I got the ilok authorization number typed in wrong, but I can't even find out where to find again the authorization number! .

Do the ilok assets appear correctly in the ilok manager?

[Mr. Kelly]

The numbers appeared to go through correctly. I think if they were inputted incorrectly... ilok would kick them out.

Geeze... what to do, what to do.

I do have an email in to Lex. Wonder how long it will be for a reply?

[sw rec]

If you're on PT 10, make sure you install the 32-bit AAX plugins. I have these running on PT10 and PT11 (64-bit AAX) both without issue. You're gonna like them a lot when you get them running.

[TOM@METRO]

Installed and running fine here. Win 8.1 PT11.3.1 AAX64.

[Mr. Kelly]

Originally Posted by sw rec

If you're on PT 10, make sure you install the 32-bit AAX plugins. I have these running on PT10 and PT11 (64-bit AAX) both without issue. You're gonna like them a lot when you get them running.

This did it! Thank you all for your thoughts...

Plus, Lexicon customer support did a fantastic job of getting back to me with the answer, as well. They had an answer for me within hours of opening today! I haven't yet been home to try it, but it all makes sense.

I installed the 64 bit version, thinking it was to coincide with my 64 bit OS, but it's the bit rate of the plugs that is relevant, so I needed 32 bit. Makes complete sense, now!

All the best, ok?