|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
Help! Omni won't connect after PT9.03 update
I made the mistake of updating to 9.03 before checking if others had problems. In hardware profiler it says the driver for this PCI slot is not installed. I tried downloading a separate version of the driver as well to no avail.
Help much appreciated. OSX 10.6.7 PT9.0.3 Omni HD / also use with Logic Model Name: Mac Pro Model Identifier: MacPro5,1 Processor Name: 6-Core Intel Xeon Processor Speed: 3.33 GHz |
#2
|
|||
|
|||
Re: Help! Omni won't connect after PT9.03 update
come on guys... have to get a project out today and I'm sure I just missed something obvious?
This is a Westmere Processor all was fine till the update. |
#3
|
||||
|
||||
Re: Help! Omni won't connect after PT9.03 update
Mine is working fine with 9.0.3.
I'd try re installing Pro Tools and the device driver. |
#4
|
|||
|
|||
Re: Help! Omni won't connect after PT9.03 update
r u using an HD interface? I really don't know why it would work fine until the update.
I may just revert to an older version of MY HD. Go back to 9.02.... ugh! |
#5
|
||||
|
||||
Re: Help! Omni won't connect after PT9.03 update
Yeah, I'm on an Omni.
|
#6
|
|||
|
|||
Re: Help! Omni won't connect after PT9.03 update
There isn't a separate driver update right? You just updated PT9.02 to 9.03 ?
Where is the driver stored on the hard drive? I can't find where to dump... thanks! |
#7
|
|||
|
|||
Re: Help! Omni won't connect after PT9.03 update
Try holding the "N" key while you launch PT? That should allow you to pick an interface.
If that doesn't work, reset the Omni. I had to reset mine to clear up some funky stuff. Also, are you on the lastest firmware? If not and you choose to update, reset the Omni again afterwards. Good luck! |
#8
|
|||
|
|||
Re: Help! Omni won't connect after PT9.03 update
Thanks for the help. I got it fixed. I kept wanting to just replace the driver, but finally found in one of the install pdfs that drivers for the HD Native card are actually included in the PT software, NOT a part of the PT9 Drivers update.
So the obvious answer was really the right one after all. I did a "safe" uninstall of PT then the fresh install. Would have done that initially except the fact that there are separate PT native drivers. Does anyone else get confused by the fact that the names of all the PT product lines sound the same? ugh! anyway, thanks! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Maudio Profire connect to HD Omni? | Lpmike75 | Pro Tools HDX & HD Native Systems (Win) | 6 | 01-22-2014 08:54 AM |
Eleven Rack won't Connect to Omni IO | Regg-4 | Eleven Rack | 1 | 10-19-2013 10:08 PM |
HD Native can't connect with Omni | Jace Everett | Pro Tools HDX & HD Native Systems (Mac) | 6 | 05-10-2012 03:47 PM |
OMNI Help after 10.0.1 update | ronstephens | macOS | 1 | 02-09-2012 04:54 PM |
HD Omni firmware update | CDac | Pro Tools HDX & HD Native Systems (Mac) | 3 | 08-01-2011 11:27 AM |