|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#11
|
||||
|
||||
Re: s1 not cycling through automation modes to 'read'
No, its the Rec/Auto Switch Press changes......
|
#12
|
|||
|
|||
Re: s1 not cycling through automation modes to 'read'
Thanks. I'm relatively new to EuCon.
No change in behaviour with that setting applied. |
#13
|
||||
|
||||
Re: s1 not cycling through automation modes to 'read'
If you start a new blank session with just one mono track does it still do it? Theres got to be something specific about your setups or settings. We still can't reproduce here on multiple systems in multiple locations and I really want to get this into the 20.6 release.
|
#14
|
|||
|
|||
Re: s1 not cycling through automation modes to 'read'
Yes, same issue in a blank session with only a single mono track. Is there a tool I could run to give you some more diagnostic information? A netstat readout maybe?
|
#15
|
||||
|
||||
Re: s1 not cycling through automation modes to 'read'
and if you change the mode in PT it shows OK on the Control App? Also can you change the modes OK On the Control Apps Mixer page?
|
#16
|
|||
|
|||
Re: s1 not cycling through automation modes to 'read'
I'll double-check tomorrow when I'm back at the studio. Or maybe someone else with the same issue can confirm.
|
#17
|
|||
|
|||
Re: s1 not cycling through automation modes to 'read'
Also tested with a blank session, single mono audio track but it didn't make a difference.
When changing the mode in PT the Control app changes along with it (I checked on the meters, channel and mixer pages). Changing the mode from the Control app mixer page also works as expected. Same for the Channel page. By "as expected" I mean that changing it from the Control app causes PT to update the mode accordingly. It doesn't work from the meters page but I don't believe it's supposed to (I'm also new to the S1/Eucon workflow so I might be wrong about that). You mentioned the Rec/Auto switch option, that was how I had it set originally when I came across the issue. I just tested it again and it doesn't seem to make a difference if this option is turned on or off, same behavior either way. So from what I can tell it's only an issue when switching modes using the S1. The Control app and PT seem to be behaving as they should (to the best of my knowledge anyway).
__________________
Mac mini M1, 16 GB RAM, Ventura 13.3.1, Pro Tools 2023.3, Avid S1, UA Apollo Twin UAD-2 Satellite |
#18
|
||||
|
||||
Re: s1 not cycling through automation modes to 'read'
Can I confirm with everyone its getting stuck at Latch ?
|
#19
|
|||
|
|||
Re: s1 not cycling through automation modes to 'read'
Yeah, that's what happens for me.
__________________
Mac mini M1, 16 GB RAM, Ventura 13.3.1, Pro Tools 2023.3, Avid S1, UA Apollo Twin UAD-2 Satellite |
#20
|
||||
|
||||
Re: s1 not cycling through automation modes to 'read'
Can you all post an image of your Surfaces page from EuControl or give a description of what you have and in what order.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Global Automation Modes (and more...) | PatrickCusack | Avid S4/S6 | 1 | 04-10-2018 09:36 PM |
System 5 MC Automation Modes | Mike Hybrid | System 5 | 6 | 07-10-2014 02:14 PM |
Shortcut for cycling automation | SZE | Post - Surround - Video | 3 | 09-24-2009 09:47 AM |
change automation modes? | Richard Fairbanks | ProControl, Control|24, Command|8 | 2 | 07-11-2007 04:02 AM |
bcf2000 & automation modes?HOW? | maltezze | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 1 | 10-29-2006 06:59 PM |