|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
Signal strength over distance
How far can a typical microphone/line signal be carried over a standard cable or snake? At what point do you need to boost the signal?
|
#2
|
|||
|
|||
Re: Signal strength over distance
i don't have the answer (sorry about that), but this is a great question. i would love to hear some info about it.
and if anyone has any info, here is another question... whats the best way to boost the signal when getting into this dangerout terratory. thanks!
__________________
www.TheSoundCoop.com www.youtube.com/TheSoundCoop PCAudioLabs 2.5GHz Quad-Core Q8300 FSB:1333/1066MHz, NB:IntelG33, SB:Intel ICH9DH/WinXP Pro SP3 / SATA HD's = 160GB(7200/8), 320GB (7200/16) x 2,500GB (7200/32) / 4GB DDR2-800 / FW = TI ChipSet / Gear: Apogee Rosetta800, ADL600, Avalon2022 // M-Audio = Profire Lightbridge, Octane 8's, BX5's BX8's & SBX // ProTools MP 8.0.5 w/ MPTK 2 - Velvet Waves Sonnox IK NI FXpansion Massy -- DVerb2.0 Test = 230 verbs |
#3
|
||||
|
||||
Re: Signal strength over distance
Mic signals can go a long ways - 100+ feet or more, because they're low impedance signals.
Line level signals, on the other hand, start to peter out around 25 feet, as they're high impedance. Converting to low impedance (with a direct box) allows you to run them for longer lengths. That's the best method, as continually boosting the signal just raises the noise floor of the signal, degrading sound quality. |
#4
|
|||
|
|||
Re: Signal strength over distance
Quote:
In a large-venue concert, you might have mic signals traveling down 300 feet of mic cable/snake cable to get to the mixer. The signal looses a little something going that distance, but it's OK for live sound, but might be noticed in a recording. Converting to digital on stage (close to the mic) can cut down on a lot of the long-distance loss. I have run a dynamic mic through over 1,000 feet of cable for an outdoor event with no problems, but then that was for a sports announcer, not for critical music. If your recorder is a long distance from the microphone, it's best to keep the mic cable short and allow the cable between the preamp and the recorder (assuming a balanced line) to be longer. Some recording trucks will place their preamps on stage and then run balanced line-level signals out to the truck.
__________________
www.barnabas.com Barnabas MultiMedia |
#5
|
||||
|
||||
Re: Signal strength over distance
Quote:
My numbers are also extremely conservative, fwiw. |
#6
|
|||
|
|||
Re: Signal strength over distance
Thanks for the help!!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Strage Beat Detective Conform Strength Behavior | sleiweke | Pro Tools 10 | 0 | 02-06-2012 01:02 PM |
OT - how do you distance yourself? | Stig Eliassen | General Discussion | 19 | 10-27-2010 03:43 AM |
Maintaining volume strength in fades? | Ken P | Tips & Tricks | 3 | 10-13-2006 11:53 AM |
Managing input signal strength during tracking liv | dicknash | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 5 | 03-11-2004 08:53 AM |
Using one signal to lower the volume of a second signal for distance learning? | Bastiaan | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 7 | 04-23-2003 12:54 AM |