|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
KR7A need help tweaking
Hey guys i just got this mobo and so far everything runs very smooth .On the Davec test i got 24 + 9aux.But i've seen better than that.So if any body out there with the same Mobo,any advice on tweaking>this resolts are without chainging anything,just installed PTle.My system is: Abit KR7A KT266a
AMD1.4 THbird Promise Ultra ATA100TX2 2 Maxtor 7200rpm I read somewhere that is better for DIGI to have higher IRQ than Promis.Right now the Digi is on 5 and Promise is on 10.Do i need to chainge that,also the temperatur on the CPU is runing around 147. Is that normal for AMD's.Thanks a lot!!! |
#2
|
|||
|
|||
Re: KR7A need help tweaking
Hello Valeri,
I don´t know what your CPU temperature means in Celcius but from what I know when idle it shouldn´t get over 60° Celcius and when strained not above 70°. ( AMD says Athlons max should be 90° but some users seem to have experienced the treshold as lower. ) I have the same mobo running better. I think I posted the slot management in the Davec test thread. But I don´t use the promise card, so things might differ for your setting. If you have RAM that can handle tweaking you could try doing it within the bios. I did it like this: ( FSB at 136 MHz ) 1. "FSB rate" in softmenu III to 4:4:1 2."Chipset driving controll" -> default 3. The optimal "super bypass wait state" is 0 cycles, but should be set to 1 ( for 133 MHz)for priority of stability. 4. "SDRAM time settings" -> as low as possible 5. "SDRAM ph limit" -> as high as possible 6. in "DRAM clock / drive control" raised DDR voltage to 2.65 or 2.75. FSB to 136 or 138 MHz, "no" "by SPD"! 7. "DRAM timing to manual. 8. "Bank interleave" to 4 9. "Precharge" to active 10."TRP" to 2T 11."Active to precharge" TRAS to 5T 12. "Active to CMD" ( TCRD ) to 2T 13. "DDR DQS" to auto 14. "DRAM queque depth" to level 4 15. "DRAM command rate" to 1T In Windows: 1. System->Performance->File system: check "Disable write behind caching for all drives" 2. "Hard disk" / "Read ahead" to none 3. ( If you have 256 MB DDRAM )"Specify virtual memory" min 256 / max 256 ( But this dicussed differently some advice disabling it at all. You can try one after the other, look what works best.) 4. Performance-> Computer role: set to network server. Cheers |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tweaking | Bigpit | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) | 5 | 04-19-2008 12:51 PM |
Tweaking your Ram | stevedresser83 | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 3 | 02-09-2008 01:43 PM |
Tweaking XP For 002R | fabpab | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 6 | 07-14-2005 04:18 PM |
xp tweaking | pauleddy2 | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 1 | 08-03-2002 08:49 AM |
Abit KR7A KT266A -Help me !!! | Pelikan | 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Win) | 1 | 01-08-2002 06:59 AM |