Avid Pro Audio Community

Avid Pro Audio Community

How to Join & Post  •  Community Terms of Use  •  Help Us Help You

Knowledge Base Search  •  Community Search  •  Additional Resources


Avid Home Page

Go Back   Avid Pro Audio Community > Pro Mixing > Artist Series

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-14-2016, 08:10 AM
michael@sounddesign&mix michael@sounddesign&mix is offline
Member
 
Join Date: May 2015
Location: 550
Posts: 10
Default Artist Mix & Control suddenly not connecting

EuCon 3.3
PT 12.5.0
Logic X
OS 10.10.5

I've been succesfully using the Mix & Control for 2 years. I went on vacation and powered them down for a week. Came home, turned them on and Eucon will not recognize them at all. All cables are the same. Signal flow is as follows.

Surfaces to Router (straight ethernet cable)
Router has lights on and recognized all ethernet cables
Router to Thunderbolt Ethernet MBP connect (straight cable)
Network Pref: Ethernet prioritized to top. Set to DHCP. Gives an address of 169.254.62.2, subnet mask 255.255.0.0 I should mention the Thunderbolt Ethernet is lit YELLOW and say it has a self assigned IP and will not be available to the internet, but I assume this is normal as of course it's not connected to the Internet, it's connected to my surfaces.

Eucon Sys Pref: Network Interface: Thunderbolt ethernet Launch Status: Pending - but never finds the surfaces. I don't have a "stop" button as mention in other posts.

EuCon App; No surfaces show up at all. Not in PT, or Eucon or even the Finder. I've been thinking about just going straight into a surface, but I don't have a crossover cable, and I don't think this is a cable issue. They worked before and a cable can't break itself. I'm thinking it must be a network issue on my MBP as I was configuring a wireless router while on vacation.

Any help would be greatly appreciated. I've gotten so used to the surfaces I can't work without them.

Thanks,

Michael
Sound Design & Mix
Reply With Quote
  #2  
Old 09-15-2016, 07:22 AM
michael@sounddesign&mix michael@sounddesign&mix is offline
Member
 
Join Date: May 2015
Location: 550
Posts: 10
Default Re: Artist Mix & Control suddenly not connecting

Problem solved;

Tested Thunderbolt ethernet with my modem to make sure I was getting a connection.

Uninstalled EuCon 3.3
Installed Eucon 3.4.1 and updated firmware.

All was fine. I guess EuCon just got stupid.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Eucon 3 - Artist Control not connecting to PT Trazan Artist Series 50 04-04-2016 04:14 AM
2 avid artist mixes and one artist control V2 for sale Brandonx1 Buy & Sell 2 03-21-2016 10:55 PM
Avid Artist Mix Series Suddenly is NOT working in Pro tools 11.3.1! shamanrock Artist Series 3 04-03-2015 11:22 AM
Artist Mix: Faders 3 & 4 suddenly acting odd... Suges Artist Series 10 07-13-2013 01:27 PM
Touching Artist Transport Freezes Up Artist Control in Logic sonofmack Artist Series 1 03-13-2013 09:22 PM


All times are GMT -7. The time now is 03:56 PM.


Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com