Avid Pro Audio Community

Avid Pro Audio Community

How to Join & Post  •  Community Terms of Use  •  Help Us Help You

Knowledge Base Search  •  Community Search  •  Additional Resources


Avid Home Page

Go Back   Avid Pro Audio Community > Pro Mixing > Artist Series

 
 
Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 01-01-2018, 08:06 AM
MicMan MicMan is offline
Member
 
Join Date: Jan 2018
Location: USA
Posts: 2
Default ProTools Not Connecting to Artist Mix

I've looked around quite a bit, and I don't see anything that directly applies, or at least solves my issue, so I'll go ahead and ask.

I just added an Artist Mix to my setup. I'm unable to get ProTools to connect to my Artist Mix. I'm using ProTools 12.8.3, EuControl 3.7.0 138, Firmware 1.5.4
  • Artist Mix is directly connected to my Ethernet port on my Thunderbolt interface
  • System Preferences/EUCON/Network Interface is set to Thunderbolt Ethernet
  • IP address on Mac is manually assigned to 192.168.255.1/24
  • IP address on Mix is manually assigned to 192.168.255.16/24
  • I can ping the Mix from the Mac
  • When Mix powers up, AVID logo appears in each channel on the Mix
  • When EuControl starts up, the AVID logo disappears, and a long thing rectangle appears at the bottom of each Mix channel
  • EuControl successfully communicates with MIX
  • System Preferences/Firewall allows all incoming connections for all ProTools, Avid, and EuControl apps
  • Wireshark shows TCP connection successful between Mix and Mac IP's
  • Mix shows up in EuControl list of My Surfaces and All Surfaces
  • Show Info pops up the name of the Mix, and the 1st channel on the MIX shows the name mix
  • I can rename the MIX to anything, and this is reflected in the Show Info information
  • I have successfully applied Update Firmware to version 1.5.4
  • Vegas mode seems to work perfectly normally

So, from the above, it appears that
  • The Mix is working expected
  • The network connection between the Mix and the Mac work fine
  • Mix is communicating properly with EuControl

Now, I go into Protools, and under Peripherals/Ethernet Controllers, I enable EUCON, and EUCON only. When I do this, a popup says Configuring Eucon.

Sometimes a few random tracks will become outlined in turquoise, but that's as far as I get. I can't get any other signs that anything is going on between ProTools and the Mix.

I've tried trashing all my Euphonix and Avid plists under ~/Library/Preferences. I've uninstalled and reinstalled EuControl a couple of times. I just don't see any improvement.

Any suggestions on a next step?

Thanks
Reply With Quote
 

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Problems since connecting two artist surfaces Mirek Artist Series 2 11-04-2016 10:33 PM
Artist Mix & Control suddenly not connecting michael@sounddesign&mix Artist Series 1 09-15-2016 06:22 AM
Need help connecting mbox2 to my protools 12 with mac Dc914 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) 7 04-10-2016 12:34 PM
Eucon 3 - Artist Control not connecting to PT Trazan Artist Series 50 04-04-2016 03:14 AM
Problem connecting the Artist series? Emcha_audio Artist Series 0 02-14-2014 07:20 AM


All times are GMT -7. The time now is 07:05 AM.


Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com