|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
Inputting a Kemper Profiling amp into Pro Tools?
Which is the best way to input a Kemper into Pro Tools?
Is the best way to DI it straight into the front of the interface or can you use it as an interface via USB. I tried using it as an interface via USB but Pro Tools wouldn't recognise it as hardware and wouldn't start up. |
#2
|
||||
|
||||
Re: Inputting a Kemper Profiling amp into Pro Tools?
The Kemper does not support recording via the USB port.
You would either have to run the main outs into your audio interface analog ins or, if your audio interface supports it, use the S/PDIF connection. |
#3
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
I use both the SPDIF and analog outs to connect my Kemper to 192 interface. Depends on what I'm planning on in the session :)
__________________
Raoul Crane
www.blaze-studios.co.uk PT 10.3.10 HD Accel 6, Mac Pro 5.1 12 Core 3.46hz Dual Boot Lion 10.7.5 and Maverick 10.9.5 32GB Ram Magma PE6R4i Chassis |
#4
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
Thanks for your held guys.
Is one method of connection clearer than the other. I tried going from the monitor out but it didn't sound as clean on clean sounds as it does through the Kemper on it's own. It sounded like the sound was being coloured somewhere a long the line. Do I take one lead from each main out and connect each lead to the interface, to input 1 and the other to input 2 on my avid Mbox 3G? |
#5
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
If you set the main out to master mono you can just use 1 lead from the main out to 1 input on your Mbox
__________________
Raoul Crane
www.blaze-studios.co.uk PT 10.3.10 HD Accel 6, Mac Pro 5.1 12 Core 3.46hz Dual Boot Lion 10.7.5 and Maverick 10.9.5 32GB Ram Magma PE6R4i Chassis |
#6
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
Spdif if you have it because otherwise you will be converting to analog and back to digital for no reason. Spdif keeps it a digital signal.
|
#7
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
I have my 2 Spdif leads now and have tried them from the back of the Kemper in out to the in outs on my mbox but nothings happening.
on the armed channel in pro tools 10 it says spdif mono l and spdif mono r which I've selected but nothing happens Any ideas how I get this up and running? |
#8
|
||||
|
||||
Re: Inputting a Kemper Profiling amp into Pro Tools?
See this post (Setting up SPDIF) on the Kemper site. They discuss how to setup S/PDIF properly.
|
#9
|
|||
|
|||
Re: Inputting a Kemper Profiling amp into Pro Tools?
Thanks very much, I'll check that out now
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
This is crazy! Kemper Profiling Amp | Benoni | Eleven Rack | 46 | 01-17-2013 06:29 AM |
Kemper profiling amp?? | Raoul23 | Eleven Rack | 18 | 01-08-2013 10:32 AM |
Kemper Profiling Amp - Video | Obsidian Dragon | Eleven Rack | 0 | 03-23-2012 06:17 AM |
NEW PRO TOOLS USER - TROUBLE INPUTTING AUDIO | JTM | Digidesign Hardware & Software | 0 | 08-23-2004 04:45 AM |
midi inputting wrong notes in pro tools | chagos | MIDI | 1 | 06-14-2004 06:44 PM |