|
Avid Pro Audio CommunityHow to Join & Post • Community Terms of Use • Help Us Help YouKnowledge Base Search • Community Search • Learn & Support |
#1
|
|||
|
|||
Avid Please Solve My HD Omni Level Problen
Hi,
i have a problem with the HD Omni Recording Level i have i drop in level about 12 dB When the HD Omni is conected to the +4dBu reference on the XLR Balanced output comming from the Langevin Preamp Duel Combo if you please how the HD Omni line in is Connected i have the langevin pramp conected Out Balanced Pin 1 = Ground shield Pin 2 = + Hot Going Signal Pin 3 = - Negative Going Signal best regards |
#2
|
||||
|
||||
Re: Avid Please Solve My HD Omni Level Problen
How are you testing?
(Is your device is the one with a Compressor and Preamp with line in and mic in?) How are you determining this level drop? (VU meters on Pre to Peak meters in Pro Tools?) How does the preamp sound (Clean...Noisy...) can you not get enough gain for a good recording?
__________________
(Help us Help You)<<<click here Profile-System Tracks: https://www.n1m.com/datatunesdetroit Apple Music https://music.apple.com/us/search?term=DatatunesDetroit |
#3
|
|||
|
|||
Re: Avid Please Solve My HD Omni Level Problen
How are you testing?
(Is your device is the one with a Compressor and Preamp with line in and mic in?) -My device is the Manley Langiven Duel Combo Preamp Connected to the line in 3 – 4 on the HD Omni From Avid How are you determining this level drop? (VU meters on Pre to Peak meters in Pro Tools?) -I was Comparing the Recorded level by the same setting for the preamp but one recorded +4dBu the other track -10dBV How does the preamp sound (Clean...Noisy...) can you not get enough gain for a good recording? The preamp sound very Clean But when I am recording with the +4dBu setting on the HD Omni I Have a Drop in level about 12 dBfs and I have to tern the gain all over to get the signal near -25dBFS Thanks for cooperation |
#4
|
||||
|
||||
Re: Avid Please Solve My HD Omni Level Problen
Ressurecting this thread.
First time I ever tried the TRS line inputs, I have the same issues!! All 4 line inputs same. verified on 3 and 4 to avoid any mic/line switching from the panel. Tested with Grace M101, and a Sound Devices MixPre. Levels down 10 to 12 dB. Had to switch Protools line input to -10 in order to get close to unity gain! Not right. Verified mic and cable via Omni front XLR mic pre inputs. No problem there.
__________________
IMDB |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FS:Avid HDX and Omni I/O | tripstation | Buy & Sell | 0 | 05-13-2014 11:12 AM |
Avid Omni for Avid HD 16 I/O+my cash | Zeljko2 | Buy & Sell | 1 | 12-20-2013 12:45 PM |
Audio level alignment across HD I/O & Omni | the.engineer | Pro Tools HDX & HD Native Systems (Mac) | 4 | 08-03-2013 02:18 AM |
Omni mirrored outputs level drop | Picture Start | Pro Tools HDX & HD Native Systems (Mac) | 0 | 04-05-2012 09:21 PM |
Avid HD Omni | ejwells | General Discussion | 5 | 08-17-2010 11:52 AM |