Behringer FCB1010 with Eleven Rack
I am using the Behringer FCB1010 Stock (No Special PROM)
It works great but you have to do your programming on the Foot Controller. I am in Bank Mode so I can have a Bank with 10 Presets, this is the way I prefer as opposed to Stomp Box Mode (I think it can do that too) For Midi Patch A1 is 1, B1 is 5, etc... I have them listed in this Spreadsheet I made. http://www.intecautomated.com/blindi...yBankv2_01.xls The Biggest Two Procedures: Preset Mapping - Which Program comes up when you press button. You have to Select the Bank with the Bank Up Down and then Select a Preset 1-10 (It should be lit up) 1) Press and Hold Down Button (2.5 sec) 2) Press Up to Confirm 3) Press 1 Button (Always 1, you selected the preset prior to Holding down) 4) Press Up to Confirm 5) Enter Patch to Recall (M4 would be 52, press 5 then 2) 6) Press Up to Confirm 7) Press and Hold Down Button to Save (2.5 sec) Footpedal Mapping - Continuous Control of Parameters You have to Select the Bank with the Bank Up Down and then Select a Preset 1-10 (It should be lit up) 1) Press and Hold Down Button (2.5 sec) 2) Press Up to Confirm 3) Press 8 or 9 Button (8 is Left Pedal) 4) Press Up to Confirm 5) Enter CC Number (11 is MultiFX, 4 Wah, Volume 7) 6) Press Up to Confirm 7) Enter Minimum (0-127, 0 is OFF and 127 Full Volume) 8) Enter Maximum (0-127, 0 is OFF and 127 Full Volume) 9) Press and Hold Down Button to Save (2.5 sec) You can also send a Toggle upon loading each preset. For instance I setup a Tuner Patch on Bank 5 preset 5 1) Press and Hold Down Button (2.5 sec) 2) Press Up to Confirm 3) Press 6 Button 4) Press Up to Confirm 5) Enter CC to send (Tuner is 69, press 6 then 9) (0 to turn off) 6) Press Up to Confirm 7) Enter Minimum (0) 8) Enter Maximum (127) 9) Press and Hold Down Button to Save (2.5 sec) |
Re: Behringer FCB1010 with Eleven Rack
Oh Yeah... Does anyone know if it is possible to Run ProTools without the Eleven Rack plugged in???
It is kind of Stupid that I cannot listen to Something I recorded unless I have my Eleven Rack plugged in... |
Re: Behringer FCB1010 with Eleven Rack
Quote:
|
Re: Behringer FCB1010 with Eleven Rack
Quote:
|
Re: Behringer FCB1010 with Eleven Rack
Quote:
http://www.eurekasound.com/eurekaprom/configurations/11 |
Re: Behringer FCB1010 with Eleven Rack
Quote:
|
Re: Behringer FCB1010 with Eleven Rack
Quote:
Someone told me the other day that prior to PT 9, even full versions of PT required a piece of Avid hardware attached to startup. I can't comment on that - though I've worked on many PT systems over the years, I've only OWNED LE systems up until PT 9 and 10... |
Re: Behringer FCB1010 with Eleven Rack
Quote:
with the introduction of 9 though, they did away with "LE" and went to pro tools pro tools hd pro tools mp (m powered m audio products) pro tools se (also for m audio products) the first 2 authorize w ilok and can work with any core audio or asio compliant device. the last 2 will only work on selected m audio hardware. |
Re: Behringer FCB1010 with Eleven Rack
Quote:
|
Re: Behringer FCB1010 with Eleven Rack
Quote:
But thats only if you have Pro Tools 9 or 10. Quote:
|
All times are GMT -7. The time now is 08:29 AM. |
Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com