Avid Pro Audio Community

Avid Pro Audio Community (http://duc.avid.com/index.php)
-   Technical Alerts (http://duc.avid.com/forumdisplay.php?f=32)
-   -   Pro Tools 7.4cs3 Updates for all 7.4 Systems (http://duc.avid.com/showthread.php?t=217010)

Avid 03-01-2008 11:15 AM

Pro Tools 7.4cs3 Updates for all 7.4 Systems
 
Pro Tools 7.4cs3 updates for all Pro Tools 7.4 systems are vailable for download from the Pro Tools CS Updates page:
www.digidesign.com/support/csupdates

And related support sections for Pro Tools 7.4 software and hardware.

Previous installation of Pro Tools 7.4 required to use these updates:In addition to previous items from Pro Tools 7.4cs1 and 7.4cs2, the following fixes are included in Pro Tools 7.4cs3:

Pro Tools HD 7.4cs3 for Mac & Windows

Fixed: Surround Pan Automation is not Updating Properly in Loop Playback (Item # 85802)
The pan positions are correct on the first play of the selection, but can be incorrect on subsequent plays

Fixed: Playback of Surround Panning automation gets "stuck" (Item #100847)
This would only occur when writing automation with a selection highlighted while in Loop Playback mode

Fixed: Trim Values Could Be Accidentally Written To The Entire Session (Item #100795)
Steps to reproduce:
- A fader position in Latch/Trim or Touch Trim could be accidentally bumped while the transport was stopped.
- Subsequently leaving Trim mode, or manually coalescing trims would then write that bumped value to the entire track

Fixed: Pro Tools Automation Thinning Could Sometimes Remove Non-Redundant Breakpoints (Item #100794)
The thinning algorithm could mistakenly classify a breakpoint as redundant

Fixed: Certain Third Party Products Could Cause Pro Tools to crash (Item #100661)
Celemony Melodyne and AudioEase Snapper would cause a crash with tick-based regions (introduced in Pro Tools 7.4)

Fixed: Mojo - PAL QuickTime or MXF Movies Could Stutter or Display in Black and White (Item #101047)
This resulted from Mojo getting "stuck" in NTSC mode even when Pro Tools was set to PAL

Mac Only:
Fixed: Scrubbing Avid Video on the Computer Monitor Would Resize the Picture (Item #100657)


Pro Tools LE 7.4cs3 for Mac & Windows

Fixed: When Monitoring All Inputs on 003 Factory, Random Pops and Clicks Could Occur on Inputs 4-8 (Item #101084)
Although this is not likely to occur on 003 Rack, this update is recommended for both 003 Factory (console) and 003 Rack

Fixed: Pro Tools Automation Thinning Could Sometimes Remove Non-Redundant Breakpoints (Item #100794)
The thinning algorithm could mistakenly classify a breakpoint as redundant

Fixed: Certain Third Party Products Could Cause Pro Tools to crash (Item #100661)
Celemony Melodyne and AudioEase Snapper would cause a crash with tick-based regions (introduced in Pro Tools 7.4)

Fixed: Mojo - PAL QuickTime or MXF Movies Could Stutter or Display in Black and White (Item #101047)
This resulted from Mojo getting "stuck" in NTSC mode even when Pro Tools was set to PAL

Mac Only:
Fixed: Scrubbing Avid Video on the Computer Monitor Would Resize the Picture (Item #100657)


Pro Tools M-Powered 7.4cs3 for Mac & Windows

Fixed: Pro Tools Automation Thinning Could Sometimes Remove Non-Redundant Breakpoints (Item #100794)
The thinning algorithm could mistakenly classify a breakpoint as redundant

Fixed: Certain Third Party Products Could Cause Pro Tools to crash (Item #100661)
Celemony Melodyne and AudioEase Snapper would cause a crash with tick-based regions (introduced in Pro Tools 7.4)


All times are GMT -7. The time now is 09:51 PM.

Powered by: vBulletin, Copyright ©2000 - 2008, Jelsoft Enterprises Limited. Forum Hosted By: URLJet.com